Lisa Battig: The Interview Issue, September 8, 2017

NOAA TAS Lisa Battig

Aboard Fairweather Alaskan Hydrographic Survey Ship

September 8, 2017

Location: Coast Guard Base, Kodiak Alaska

Weather from the bridge: 48o F, 1-2 knot wind from, Completely overcast,

XO Gonsalves

Executive Officer Michael Gonsalves in his overwhelming (because of all the things he does) office.

An Interview with XO (Executive Officer) Michael Gonsalves

How long have you been with NOAA?

I’ve been here for 13 years…I’ve been on the ship for about 6 months.

What brought you into NOAA?

Certainly I’ve always had an interest in the ocean and in the environment. One of my undergraduate degrees was in oceanography. So I think that’s what steered me towards NOAA. My other undergraduate degree was in math, so I liked the idea of being able to apply math in an environmental setting.

As a side note, XO Gonsalves also has a MS in Applied Math and a PhD in Marine Science

What is it that you do – what is the job of an executive officer?

The Executive Officer position is second in command. So if anything should happen to the CO (commanding officer) I would assume command. Though that is a contingency; that is not my actual job… All administrative work goes through me. For example, the budget, payroll, travel, performance, disciplinary actions, scheduling, arranging all port logistics, …getting augmenters to come out to the ship to fill in… I do everything to allow everyone else to do their job. My job is not the mission. My job is keeping the ship safe and logistically ready to execute the mission.

This is typically a step on the path to becoming a CO, is that correct?

Typically, that’s right. Usually the average NOAA Corps officer will have four sea assignments. Basically every five years, give or take, they will be going back to sea. The first will be as a junior officer, an Ensign. The second is as an Operations Officer who will be coordinating the mission [of that ship]. On the hydro ships that means coordinating the hydrographic science. The third sea tour will be as an Executive Officer and the fourth, around year 15, will be as a Commanding Officer.

I know that NOAA Corp officers spend roughly two years at sea and then three at a land billet. So what has your path been thus far?

I lingered in nearly all of my assignments by a little bit. My first assignment was here, on Fairweather, just after she was reactivated. It was a very skeletal crew. I had opportunities to be trained quickly. We only had two launches at the time. There were so few boats, there were so few people trained in doing things, it was in the crew’s best interest to qualify me because very few people were qualified to do anything.

My first land assignment was at the University of Southern Mississippi. It was a double billet. Number one, it was full-time university training. There was also working with an inter-agency group, The Naval Oceanographic Office and the Army Corps of Engineers, both also conduct survey operations. It’s a nice inter-agency group with similar issues and problems and we can share best practices and things like that. Their particular niche is airborne laser bathymetry, so they are working from an airplane.

Back to University of Southern Mississippi, what was the degree you were pursuing?

Initially it was a master’s degree as a one year program. As it happened, there was a project that I could work on of suitable interest to the joint LIDAR center. We all agreed that I could continue to work on it. The university felt that it was dissertation worthy. So I received my Ph.D.

What was your second tour at sea?

My second tour was as an Operations Officer on Fairweather’s sister ship, Ranier. All three of my assignments thus far have been on hydro ships. There is something to be said for that. It’s a little bit tricky to bring someone in from the outside. It’s a steep learning curve.

My second land assignment was working for the NOAA Operations Branch in Washington D.C. This is a part of the Hydrographic Surveys Division. They govern the field units on the large scale. So I was making the big decisions for what the hydro ships would be responsible for during that particular season. We determined what type of coverage would be needed in each area. That is then the information that the Operations Officer on the ship is working from.

What made NOAA so attractive to you?

Giving service to the US government was a big part. I happily pay my taxes. I appreciate having a police force and knowing that my meat is safe. So that was definitely a big part of it. But NOAA also has a unique mission that I found attractive. And the variety is important to me – just knowing that every couple of years the assignment will change.

And what is it that keeps you going while you’re out here at sea? Is there anything you miss or are looking forward to when this sea tour is complete?

People are tricky and a lot of my job involves personnel. The whole job keeps me going, really. I do miss Washington, D.C. – the public transport, the museums and the shows. There are so many things to do and see. There are a lot of jobs in D.C. and I am making clear that is a desire for the next land billet.

ENS Calderon

ENS Carroll

Junior officers, ENS Calderon and ENS Carroll on the bridge working on the computer navigation system. Both also are intimately involved with the surveying program.

A quick one question survey for the junior officers on the ship… Why did you choose a hydrographic survey ship? A collection of the answers I received are below:

  • To have the opportunity to be much more deeply involved with the science
  • My background is math or math/mapping
  • To be in Alaska
  • This is a route to pursue flying with NOAA Corps
  • Didn’t want the technical skills developed in prior work to go to waste
  • Had already worked on fisheries ships with Department of Fish and Wildlife

As with all officers in our uniformed services; NOAA Corps officers have had degrees conferred prior to service. Most of the degrees are math and science. The hydrographic survey ships tend to attract the math, physics, and geological science degrees for obvious reasons. Many then go on to pursue advanced degrees as did LCDR Gonsalves, the focus of my interview.


An interview with Kathy Brandts and Tyrone Baker; Ships Stewards

How long have you been cooking for NOAA Ships and what were you doing prior?

Chief cook Tyrone in the kitchen

Chief Cook Tyrone Baker, master of the grill

T: I cooked for the Navy for 20 years out of school. When I finished, I went to work for a casino for a while – still cooking. Then NOAA called me up (he had put in an application a while before and forgotten about it) and here I am! That was back in 2005.

K: I started out in the Coast Guard…I wanted to be a bosun [boatswain] mate, which is what everyone wants to do. But it was going to take a long time to make grade, and hardly anyone wants to be a cook because it’s a lot of work. I decided to go through their school, which was two months. That was when it started, in ’94. My first ship assignment was the Polar Star, which was an ice breaker.

Chief steward Kathy B and me

Kathy Brandts, Queen of the kitchen – also known as the Chief Steward. This is the day she let me cook a bit with her.

Kathy, why did you get out of the Coast Guard and what finally got you to NOAA?

K:  All of the land assignments were being contracted out to [private companies]. So I was never going to get a chance to cook on land. So I decided that wasn’t for me. I got out after my four and a half years. I landed in Seattle, and that’s where NOAA was based. I had heard about them when I was in the Coast Guard. I knew they were hiring, talked with somebody, and essentially got hired on the spot. And I was in Alaska! I started out in the augmentation pool, I worked on Discovery and then on Ranier. Then a permanent position came up and I jumped at it. I didn’t really get along with the Chief Steward, though – so I left NOAA and worked for Keystone Ski Resorts in Colorado at their stables. [She spent several years on land at that point.]

The Chief Steward on Ranier tracked me down [in Colorado] and asked me to come back. There was talk of Fairweather coming back online and I wanted the Chief Steward job. I didn’t have the experience at that point, so I took a year off and went to Culinary School. I applied for the Chief Steward job on Fairweather and got it. I was on Fairweather from 2004-2013. [She is now the Chief Steward on Ruben Lasker, another NOAA ship, but is helping out on this leg]

Why be a ship cook?

T: I’ve been so many places and seen so many things I wouldn’t have otherwise seen. I’ve really been all around the world. I’ve been in almost every port of the world. How many people can say that? I wouldn’t trade it.

K: I was a restaurant cook for a while. I hated it. You’re either going 9 million miles an hour or there’s nothing. There’s a lot of alcoholism and drug use in that industry and they live a different life. The service industry… (laughs). And people are either sailors or they’re not. I think, much to my chagrin, I found it out after I quit the Coast Guard.

T: Yes, I agree. I’m a sailor. It was why I joined the Navy.

What are the best and most rewarding things about what you do?

T: I just really like it. I enjoy the cooking. I enjoy the work.

K: I like good food and I like when people are appreciative of what I do. And we’re all stuck out here together, why not make it the best that it can be. Meal time is what you look forward to when you’re on a ship.

David GVA and me

GVA Dave – he just joined Fairweather and was actually helping out the stewards on this leg, but now he’s where he’s supposed to be in the deck department.

Crew member of the Day: Electronic Technician (ET) Charlie Goertzen 

Charlie and me

Charlie Goertzen, tech guy extraordinaire!

So today as we pulled into Kodiak, the news came in that the long awaited new televisions were here. Immediately, Charlie was notified. And he will work hours to make sure that each crew member has a working television in their room.

He is the guy that keeps the connectivity going in pretty difficult conditions. He has to spend a lot of time keeping various computer components talking to each other. He has to content with all of the complaints about lack of bandwidth, slowness of applications, slowness of wireless – and he does his best to keep things optimized and clean and efficient all the time. Two of the things he loves the most are the ocean and working with electronic components. He gets both of them all the time!

Lisa Battig: The Inner Workings of Fairweather…

NOAA Teacher at Sea Lisa Battig

Aboard Fairweather, Alaskan Hydrographic Survey vessel

September 5, 2017

Location: 56o20.5N  166o07.1W  (We are currently ~ 170 miles due east of the Alaskan Peninsular National Wildlife Refuge!)

Weather from the bridge: 51o F, Wind 8-10 knots from 285o, high thin clouds, seas 2-3 ft (1 hour after I wrote this we were socked in with fog, which is fairly common for this part of Alaska during this time of year.)

Science and Technology Log:

Fairweather was commissioned in 1968 and has 2 engines. The engines are pretty ridiculously big. They are diesel combustion engines and run similarly to a diesel tractor engine.

Karla at the engine

Karla Martinez standing next to one of the engines for scale. She is an oiler, and currently the only female member of the engineering crew. Go Karla!!



She was built with Controllable Pitch Propellers. This technology is fascinating!! It allows for very fine control of the ship’s motion.

CPP in two positions

An image of a CPP propeller with blades in two different positions to show the axis of movement. Image courtesy of Schottel website. 

The CPP technology works by turning each of the propeller blades on its individual axis. In this way, the propellers never have to change the direction of spin, but instead the spin continues the same direction but the ship can come to a stop and then reverse direction. This differs from the fixed propeller system that is on the small launches. The Fairweather’s propeller blades are about 3 feet each in size for a total propeller diameter of 7 feet.


She also has a bow thruster which can be used in certain circumstances. The bow thruster enables the bow to move from side to side while the stern of the ship is static. It is essentially a propeller mounted into a tunnel/hole in the bow giving thrust perpendicular to the typical direction of travel. For a large ship like Fairweather, this is especially helpful when moving in and out of docking locations.

The next two technologies are of particular interest for my environmental science classes. Because the ship is often at sea for extended periods, it is necessary to make fresh water from the salt water. Typically Fairweather will take on ~16,000 gallons of water in port, but evaporators will be used to generate supplemental freshwater when it is needed.

Evap seawater in line

This is the seawater intake for one of the evaporators.

The evaporators on Fairweather are flash (plate) evaporators and they can generate around 160 gallons of water per hour when operating optimally. The evaporators are running a distillation process by evaporating the water using heat from the boilers at a low pressure and then separating the freshwater from the brine (highly saline water). Because of the constant removal of salt from the water, the evaporators need to be cleaned often for best use.

Flash evaporator

This is one of the flash evaporators. Inside the pressure is lowered and the temperature runs at about 170 degrees F. While this is below the normal boiling point of water, the water will still vaporize and condense due to the low pressure

The brine is then discharged and the freshwater is added to the supply tanks. When leaving the tanks, it is pumped to higher pressure and further treated through filters and with UV light to kill off any bacteria that may have made it through. That water is stored in a hydropneumatic tank at high pressure so that water can be delivered to all parts of the ship without the need for continuously running pumps.

People eat and drink and then they pee and poop. They also like to shower and brush their teeth and wash their hands. They also need water to drink and cook with and to make coffee and tea. Obviously there is also a lot of gray water (sinks and showers) and black water (toilets) that is produced on a ship of this size carrying ~40 people. So what is done with all of it? Well, blackwater goes through the MSD (marine sanitation device) before it is discharged outside of 3 nautical miles from land. MSDs are standard on all ships and work similarly to land based sewage treatment on a much smaller scale. Gray water can be acceptably discharged as is in most places, but must be stored within NDZs or No Discharge Zones.

Discharge plan

Guidelines for discharge

Other necessary technologies on the ship are the refrigeration system, the boilers and the generators. But I won’t go into all of those processes. It’s just amazing to me that there are so many things that must be accounted for on a ship if it will be at sea for multiple days!

Crew of the Day! Engineering


If you’re going to get pictures of the engineering crew, you have to find the rare times when lots of them are together… you can find a good group at mealtimes or when the ship is being docked and they all need to be on the boat deck! L-R: Sean, Kyle, John, Mick and Ray


L-R Sean, Connor, John, Mick, Alex, Eddie… and even with all my stealth, I’m still missing a couple from the group pictures!

The Engineering crew on this ship is a highly eclectic bunch! They are also a REALLY difficult group to get together for pictures. They have about a 40 year span in age and include folks from all over the world with a great diversity of backgrounds. There are several levels within the engineering crew. The entry level position is termed a wiper, next is an oiler, and then engineering utility, and junior engineer. These positions are unlicensed, analogous to enlisted positions in the military. The licensed positions are 3rd Engineer, 2nd Engineer, 1st Engineer and Chief Engineer. There are five licensed engineers on board right now and another six in the department who are oilers and junior engineers.

Anything that is mechanized, motorized, has an electric cable going to it, or needs to be oiled or lubed, those things all fall under the watchful eye of the Engineering crew. One of the young 3rd Engineers, Connor (nicknamed Titan because he really is giant) also describes them overseeing “Hotel Services” – plumbing, lighting, heating & cooling. The crew keeps a 24 hour watch whenever the ship is underway, and can take over aft steering if something were to fail with the bridge steering. They are also on watch whenever the small launches are being deployed or replaced to their cradles. If the bow thruster is being used, a crew member will also watch to see that it engages properly for use.

The well-being of the ship is in the hands of the Engineers and therefore the Chief Engineer reports directly to the Commanding Officer (where all other department heads report to the Executive Officer). The CO and the Chief Engineer really share the task of running the ship, but ultimate responsibility lies with the CO.

Personal Log:

The food! OH MY GOODNESS!!! The food on Fairweather has been terrific. There are two amazing cooks here currently. Tyrone, who is the Chief Cook, has been with Fairweather for 5 years. Prior to that, he cooked for the Navy. Kathy is the Chief Steward (which means she is in charge of the kitchen and develops the daily menus) and has been with NOAA ships cooking in some capacity for almost 20 years! You’ll learn more about her in my next blog… The Interview Issue!

So, here’s a sampling of what’s been on the menu since I’ve been here: Prime Rib, Lobster, Argentinian flap steak with Chimichurri, Halibut with some crazy good pesto type sauce… I am going to leave the ship about 10 pounds heavier than when I got here. So, this is not what you always get on NOAA ships, but this particular pairing of Kathy and Tyrone makes some serious magic!!

Lisa Battig: Of Auroras, Anemometers, Anchors and Adult-sized Exposure Suits, September 3, 2017

NOAA Teacher at Sea

Lisa Battig

Aboard NOAA Ship Fairweather

August 28 – September 8, 2017


Mission: Arctic Hydrographic Survey

Geographic Location: Transit from Port Clarence to Yukon River Delta with Ship Surveying on the west side of Norton Sound
Latitude: 62o 32.5 N            Longitude:  165o 48.7 W

Date: September 3, 2017

Weather on the Bridge:
48 degrees F, Winds 6-8 knots from NNE, Seas 2-3 ft increasing, 50% cloud cover

Science and Technology Log


Manda aurora 1

A shot of the aurora taken by Lieutenant Damien Manda, Operations Officer. This was my first aurora ever, and I know I was treated to a truly spectacular display. There was a lot of ooo-ing and aaah – ing and shrieks of delight. I was definitely one of those!

So this isn’t ship science, and it certainly isn’t technology that is made or operated by anyone on the ship, but the aurora is great science and of all the things I’ve experienced out here, has one of the best ties to Chemistry. Why Chemistry? Well, because it’s dealing with electrons. As my chemistry students will learn in a month or so, energy at certain frequencies has the ability to affect the electrons in an atom by causing them to jump up one or more energy levels. That electron does not want to stay in that higher energy position (orbital) so it will shortly drop back down. When it does so, it releases the absorbed energy as a photon of light which is what our eyes see as the brilliant colors. Neon lights follow this principle.

The aurora occurs in an oval shape around the magnetic poles of the earth – both north and south. The reason for this is that the magnetic field of the earth dips closer to earth at the North and South Pole. It is in these regions that highly charged electrons and protons from the solar wind move close enough to the earth that they will interact with the electrons in elements in our lower atmosphere; nitrogen, oxygen, argon and the trace gases.

Because each element has a different emission spectrum, the color given off will vary with the elements being charged. The green that is so often associated with auroras is from atmospheric oxygen. Oxygen in the lower atmosphere is the element that is most commonly affected by the solar wind particles. When higher altitude oxygen is affected, reds will actually be present. Nitrogen will also be charged this way, but less frequently than oxygen. Nitrogen’s color scheme is blues and purples. A strong aurora, which we had the opportunity to see, will have a mix of greens, pinks, purples, whites and blues.

ANEMOMETERS: Weather is one of the more important factors in determining ship navigation. High winds bring heavy seas; heavy moisture in the air may bring low clouds or fog reducing visibility. These factors must be figured into a navigational plan. Weather on the ship is compiled both through analog and digital means. The first wind information given to a seaman standing watch during daylight hours is the wind vane on the bow of the ship. It will tell which direction the wind is from and will give that seaman a sense of how the ship may drift off course while underway.

Fairweather anemometer

Looking up at the anemometers on Fairweather set on the flying bridge. You can see the two levels reasonably well. This is where constant weather data are being gathered which are then relayed to multiple places both on the ship and off.

The ship also has two anemometers. Both are on the mast. One is above the other physically as you somewhat see in the image. They are able to pick up exact wind speed and direction and keep record of maxima. One of the two will be chosen as dominant because the wind is less influenced by obstacles as it (the wind) travels across the ship’s surface. The anemometer chosen will feed into the ship’s digital data stream.The watch also takes data on air temperature, atmospheric pressure, cloud cover, and seas. Air temperature is taken from wet and dry bulb mercury thermometers. The difference between the wet and dry bulb temperatures will give a reading of relative humidity, also, when assessed using a psychrometric chart. A standard barometer is also on the bridge. Swell height and direction are determined by the watch crew visually, as are cloud cover and type. All of these data are recorded hourly. Digital sensors on board also take many of these readings and feed them into the navigation system and the ship’s ECDIS system. The redundancy of these processes, using both digital and analog means, underscore the importance of weather to the ship.

All NOAA ships, UNOLS (university ships) and some merchant vessels also serve as weather stations for the National Weather Service. The digital data is automatically sent on the hour. Visual data on swell direction and height and the condition of the seas is shared through another program, keeping the NWS and other weather agencies more informed of local weather activity.


watching the anchor and chain

Commanding Officer Mark Van Waes and Chief Bosun Brian Glunz checking the anchor and chain to be sure it is clear of the ship. Dennis Brooks is standing by.


When placing the anchor, the ship will initially overshoot the anchor location and then reverse back over it. This is primarily to keep the anchor and chain from ever being underneath the ship. The anchor and chain are extremely heavy and could do serious damage to the scientific equipment underneath, the propellers and even scratch up the hull. Once the ship has reversed slowly to the location, the anchor is dropped along with 5-7 times the amount of chain as the depth of water the ship is in. As the chain is dropping, the ship will continue to slowly back up laying the chain along the seafloor. The chain will then be locked, and as the anchor finally drags back, it will catch and hold. When the anchor catches, the ship will buck slightly, pulling the chain completely taut, and then because the ship will rebound, the chain will slacken. This is done twice (or more, if necessary) to ensure the anchor has really caught. The bosun and deck hands are watching over the side of the ship communicating with the bridge when the anchor is taut and slack as well. For complete safety, fixed points of land are marked on the radar and distances to each are calculated. The bridge will take measurements from these points every 10 minutes for the first half hour confirming that the anchor is set and then every half hour while at anchor.

Heaving the anchor involves “reeling” it in (similar to sport fishing) by getting the ship closer to the anchor as it is being drawn up. The goal is keeping the chain at a 90o angle to the surface of the water. Again, this keeps the anchor and chain from being able to do damage to the ship. During this process, the bridge will continually check the location of the bow relative to the anchor to insure that the hull will never cross over the chain. Once the ship is directly over the anchor, it should pull free. Finally, during the time the anchor chain is being pulled up, it must be cleaned of all the mud and debris.

washing the anchor chain

Me. Washing down the anchor chain as it comes up with SS Dennis Brooks helping hold the fire hose (it’s pretty heavy!)


Exposure suit

Me trying on a VERY large adult exposure suit. Look at those legs!!

Each week, the entire crew of the ship has an emergency drill. Because there are no outside emergency personnel available for the ship (e.g. fire department) all crew must be well trained in how to handle fires, a sinking ship, and a person falling overboard. There are many crewmembers who pursued their MPIC (Medical Person in Charge), and others who are trained in Rescue Swimming, and there are also members of the Engineering crew who are trained firefighters. But regardless of training, the entire crew needs to be clear as to their responsibilities in an emergency situation and how to communicate with one another throughout the ordeal. So once a week, an unannounced drill will be run to sharpen some of these skills.

I had the chance to be involved with “man overboard” drill today. The drill consisted of me screaming as a dummy (Oscar) with a life vest was dumped over the side. After that, a man overboard was called and the ship’s alarm system was initiated. There are differing signals for each type of emergency. As all ship personnel mustered, communication began. The Commanding Officer, Mark Van Waes, was actually the first to spot the MOB (man overboard) and fixed the location for the bridge who subsequently relayed it through ship communications. At that point, two different options were available; bringing the ship to a position next to the victim and rescuing from the ship or deploying the Fast Rescue Boat mentioned in my last post to do a rescue. Although the ship was brought around, the rescue from the ship proved too difficult. The Fast Rescue boat was deployed with a coxswain, rescue diver (outfitted in an exposure suit) and a third. The MOB was found, placed on a back board, brought back to the ship, and rescue breathing was started along with warming up of the body.

It was fantastic watching all of the different pieces of the puzzle come together to be successful.

Department of the Day: The Deck Crew!

The Deck Crew

The amazing deck crew! L-R back row: Terry Ostermeyer, Dennis Brooks, Brian ____. L-R front row: Carl Coonts, Rick Ferguson, Me, Peter “Nick” Granozio

Every department is important on Fairweather, but the deck crew does a lot of difficult tasks that are often overlooked. They are the ones who keep the ship clean and stocked with supplies. They do the heavy lifting and the fixing of anything non-mechanical. They are responsible for driving the small launches – and are indispensable to the surveys since they need to drive the lines and make the call if it gets too shallow or dangerous. They are also on bridge watch and typically have the helm, meaning they are driving the big ship, too!

Deck crew launches the small boats from Fairweather and they head up the line handling to keep everyone safe. Members of the deck crew are also on watch 24 hours a day and do constant security checks throughout the entire ship every hour. They operate all of the cranes onboard. They are responsible for the flow of materials – what will be incinerated or placed in hazmat containers or stored for later disposal – and then take care of it. Finally, they also do the physical work of anchoring and heaving the anchors. The ship certainly would not run without the deck department.

Personal Log

Getting to know the different groups of people that work here has been amazing. I’ve had opportunities to work closely with the Survey team, the NOAA Corps officers, the stewards and the deck department. I’ve had a chance to see a bit of what the engineering group does, too. I’ve learned so much about the work they do and even about the lives they led before and lead now. I’ve also learned that ship life has some big ups and downs. The work is fascinating and most of the time there are new and interesting things to do. The CO, XO and Ops Officer work hard to ensure that daily duties change often and that there is a constant atmosphere of training.

But it’s difficult to be out at sea for long periods of time, and Fairweather in particular does not have a true “home port” – so it’s virtually impossible to have a place to call home. Several of the folks on this ship have family around the area of where Hurricane Irma is about to hit (Florida, the Carolinas…) and so one of the crewmembers is on his way to Florida to make sure everything is going to be okay. On the flip side, you really do get to see amazing places and events – like the aurora at the top of my post, or Russia…

Little and Big Diomede from Kyle

The islands of Little Diomede (left, foreground) and Big Diomede (right, background). Little Diomede is American land but Big Diomede is Russian. I saw Russia!


 Did You Know?

…that exposure (immersion) suits really do extend your life? In March 2008, up here in the Bering Sea, a fishing trawler, Alaska Ranger, went down with 47 people on it. All 47 put exposure suits on prior to abandoning ship – some of them were not properly fitted, one ended up with a gash in it – but at least they all put them on. While lifeboat deploys were attempted, at least two of the lifeboats ended up floating away with no one in them. Only 2 were properly deployed and one of those took on water immediately. So exposure suits were the primary survival tool! Although 5 members of the crew did not make it, 42 were saved through the actions of the US Coast Guard and others in the 1-7 hour window after hitting the water. Some of the crew members were floating in the water in their suits for 3 hours before they were rescued! The necessity of proper training, like the weekly drills on NOAA ships, cannot be overstated. But in these worst case scenarios, even an ill-fitting exposure suit is going to give you more time.

Lisa Battig: Launching the Small Boats, September 1, 2017

Teacher at Sea

Lisa Battig

Aboard NOAA Ship Fairweather 

August 28 – September 8, 2017


Mission: Arctic Hydrographic Survey final leg

Geographic Area of Cruise: Brevig Mission, Alaska
Latitude  65 19.2N,  Longitude 166 30.7W

Date: September 1, 2017

Weather from the Bridge:  extremely variable today!!

  • Morning: overcast, 6-8 knot winds, 41 degrees
  • Afternoon: partially cloudy skies, 2 knot winds, 48 degrees
  • Late afternoon: full cloud cover, rain squalls, 10-14 knot winds, 41 degrees


Science and Technology Log

Thursday’s science was a bit different. Two boats went out to do some final surveying and follow up in Port Clarence and Grantley Harbor. Because the area of Grantley harbor to be surveyed was in less than 4 meters of water, an Ambar jet boat was used with a single beam sonar mounted aft on the port side. The second boat that went out was one of the small launches for use as a dive boat for NOAA trained divers ( The goal of the dive boat was to dive on a particular location in Port Clarence that was giving a strange image that must have been coming from a man-made structure. The sonar showed a grid pattern roughly 100m x 60m with lines 7-8m apart on the long axis and 5-6m apart on the short axis. The team felt strongly that they needed to understand what was there in order to determine if it was safe for anchoring. I’ll follow up more on this later…

I went out with the team on the Ambar. As is the case with all the small launches, the Ambar is brought down from the boat deck to the breezeway deck for loading before the actual release.

Ambar at breezeway

Ambar jet boat at the breezeway deck, loading supplies. You can see parts of the davit where it was previously cradled on the boat deck above.

All gear, materials, food (long days out there!!) and people embark prior to the final drop to the water and the actual launch. This takes a team of a dozen or so people working in coordination. Prior to the start of launch, a safety officer is required on deck to oversee the process. This might be the CO (Commanding Officer), XO (Executive Officer) or Operations Officer. Most of the other personnel involved are a part of the deck crew, including the coxswain (who drives the small launches).  A davit operator handles the control of the boat via cable(s) all the way down. The bosun (boatswain) on the breezeway deck is directing commands to the operator using hand signals. Several hands are securing the craft with ropes against the side of the ship. All of these moves have to happen in perfect coordination for the safety of everyone and the protection of the Ambar and Fairweather. Personal protective equipment is worn by all parties throughout. This includes a flotation vest or jacket and a hard hat which you can see on those on the boat in the image to the left.

Five of the other six small launches on the Fairweather undergo a similar process. Each is housed in a davit cradle and each has one or more cables to control the craft during its descent toward the waterline. The davits all shift their cradling position while the cables lift to assist in the release of the craft. Once the craft is entirely free of the cradle, it is slowly lowered down the side of the vessel to the breezeway deck for loading as described above. One boat, though, has a really cool option. This is the FRB or Fast Rescue Boat. This craft can actually be launched by the driver, which is a requirement of any FRB.

Boat on fantail

Workboat on the fantail – note the three lines attached, two at the stern and one at the bow. These are handled expertly by the deck crew during launch to keep her true.

The final craft is a workboat which is housed on the fantail. It is not used for surveying, but will often be employed as passenger transport. It is also used for pick up and drop off of material that may be used on land, such as the HorCon station discussed in my previous post. This craft is not seated in a davit cradle and is instead launched through the use of a very large crane (see image below). The crane is attached to the launch at a center point connected with three lines.

Crane on Fairweather

Crane on the Fairweather boat deck centered between four small launch davits.

The craft is moved from the position on the fantail to either the port or starboard side level with the deck and lowered to the water before loading. For this reason, it is much more difficult to keep it completely horizontal and not hitting the deck and doing damage to the Fairweather.

So back to the Ambar and what we were actually doing in Grantley Harbor. Much of the harbor is quite shallow and when a team had been in there previously, they felt that there may be some irregularity to the otherwise uniform seafloor. They had been getting some interference and scattering on the side scan. They wanted to understand why and also to get a complete picture of the harbor seafloor. With the Ambar and the single beam sonar, there is little to no danger of doing damage in extreme shallows since the equipment is not on the underside of the boat and the Ambar itself can be beached as there are no propellers.

Single beam on Ambar

Single beam sonar in its mount on the stern of the Ambar. It is in the down position as it will be when launched tomorrow.




We took the boat into the shallows with the single beam sonar to take measurements along lines to as shallow as 2m. While surveying in the shallows, we found that there were sea grasses growing and according to the Operations Officer who was on board, that may have been the reason for the interference. Regardless, we continued to survey a regular pattern in order to have good data for future charts. During this time, I was given the opportunity to drive the Ambar… which showed me how much more difficult staying a straight line course is than the coxswains make it look.



Ambar driving lines

Yep. The outlined line is my line. I am reasonably proud that I actually manage to make it from one side to another. But even that was with a WHOLE lot of coaching!!

Upon return to the Fairweather, the Ambar is reattached to the cable and brought back up to the breezeway deck. Ropes are again used in coordination to keep the boat steady as it is lifted, much the reverse of what was described above. At that point all materials are unloaded and all the people disembark. The Ambar is then hoisted back up into the davit cradle.

When I’m back in an area with lots of bandwidth, I’ll create a video post to show just how cool the launches of small boats really is…

Personal Log

Shipboard life on a NOAA vessel is quite different from life on land. First, because the ship is a twenty four hour operation, people are needed at all hours. Many of the positions on NOAA vessels run on a 4 hours on, 8 hours off cycle. Some positions have recently shifted to 4 on, 4 off, 4 on, 12 off to afford greater lengths of time for sleep. When you are on the lower decks, it is also easy to lose track of time – and of course when you’re in Alaska during summer, it’s still light out at 10 o’clock. There are auroras to potentially be seen in the wee hours and multibeam surveying that happens through the night. There are always people up and about doing things – so the ship is a busy place at all times.

And with this in mind, I have to admit I have not been doing a great job getting to sleep. But I do sleep well on the ship, the rocking is the best cure for insomnia I’ve ever experienced. And I have been eating incredibly well – and I mean INCREDIBLY well. Mealtimes are the same each day, so that’s a great help. I will talk more about the food and the kitchen in a future post. Fortunately, with all that good eating, there’s a gym on board, so I’ve been able to work some of it off. There’s also laundry on board and a lounge with lots of movies. I like it. And waking up to the ocean and a lovely sunrise each morning makes the tiredness not really matter much.

Little and Big Diomede 2

Light early in the eastern sky – the sun comes up all around you this far north. It’s truly lovely.


As a part of NOAA’s mission, we had the opportunity to go ashore at a small town at Port Clarence called Brevig Mission. It is a town of almost 400, most of whom are native to Alaska. While ashore, we were able to spend time talking with the people, purchasing some of their handcrafts and fish, and even visiting the school. The people live simple lives. They still hunt walrus, seal and whale and those foods are the staple of their diet through the frozen winter months. I found it fascinating that they use all of the parts of the animals – the items that I purchased were from seal and walrus.

ornaments from Brev Mis

On the left is an ornament made of seal fur and on the right is a pendant of walrus tusk.



The CO (Commanding Officer) also arranged for ship tours for people from the town. The folks were taken in the Ambar out to the Fairweather in small groups and shown around. It was fun speaking afterward with those who went – there was a lot of excitement! I am so grateful that I had the opportunity to go to the town. They have a crazy history (see the “Did you know?” section below.)

Brev Mis Fam on ATV

Mom with her two little girls down near the water on their ATV. This is the most common form of transport around Brevig Mission.


Did You Know?

Cross commemorating Brev Mis 1918 flu victims

This cross memorializes all of the residents of Brevig Mission who died in the 1918 flu. It now lays on the ground aside the mass grave. All of the names and ages of the victims are listed.

Brevig Mission was hit hard by the 1918 Spanish Flu, perhaps in percentage mortality, the hardest hit place in the world. Of the 80 residents of Brevig Mission, 72 succumbed to the flu and died in a 5 day period. It was absolutely devastating. One of the current residents shared with me that reaching 400 is encouraging to the town and everyone there believes that the town is continuing to grow.

Mass grave Brev Mis 1918 flu victims

This is the location of the mass grave from the 72 flu victims of the 1918 Spanish Flu. It is a sobering place.

In 1997, the lungs of a well-preserved victim in the mass grave were shipped to a molecular pathology lab in Washington, D.C. and the flu virus was reconstructed. The evidence showed that it was a bird flu (similar to the avian flus which plague our world today) but incredibly virulent as it passed from birds to humans. You can read more about the findings here. (

Continue reading

Lisa Battig: Nome, Alaska & Launch 2808, August 30, 2017

NOAA Teacher at Sea

Lisa Battig

Aboard NOAA Ship Fairweather

August 28 – September 8, 2017


Mission: Hydrographic Survey leg IV

Geographic Area of Cruise: Alaska

Date: Wednesday, August 30, 2017
Location: Port Clarence: 65o14.034N 166o43.072W

Weather on the bridge:
30+ knot winds, 42o F, 4ft seas, heavy stratocumulus clouds (9/10 coverage)

Science & Technology Log

Over the past two days I have been introduced to tremendous amounts of the science of hydrography. In this blog post I will focus on the hardware used and the process of surveying. There are two types of sonar that are being employed. The first is side scan sonar and the second is multibeam sonar.

Side Scan

Side scan array sonar housed underneath one of the small launch vessels


Side scan is shorter range and performs better in shallower water. Side scan is used in conjunction with multibeam, however, as side scan does not give true depth values. The function of side scan is to show features evident on the ocean floor. For this reason, multibeam is run in conjunction with side scan in order to keep an accurate record of depths.


Multibeam sonar housed underneath another of the small launch vessels

Multibeam shows an exact depth. Due to the fact that it is an angular spreading band from the center of the underside of the launch, at shallow depths it will only show a very narrow strip of ocean floor.

Stop and imagine…a lit flashlight shining on a wall from only a few centimeters away. What happens to the image on the wall as you pull the flashlight back? The area of coverage of the image will become larger. The concept is similar for the multibeam in shallow versus deeper water.

Using multibeam in shallow water then would create a need for more passes closer together in order to cover an area. There are instances where using this technology even in shallow water would make sense, but for a full coverage survey, this would not be the case.

CTD Image 2

A CTD; it contains sensors for conductivity, temperature and density of the water column

The third piece of hardware used for the standard small boat launch hydrographic surveys is the CTD device. The CTD will measure conductivity of the water and also give both a temperature and density profile. The CTD is deployed multiple times during a survey as a tool to calibrate the data that is coming in via the sonar. Conductivity of the water gives an estimate of the total dissolved solids in the water. This information, along with the temperature and density will give an estimate of sound speed through the water column.

Stop and try this one for better understanding… knock on a door normally with your head roughly arm’s distance from the point where you are knocking. Now repeat the process of knocking, but with your ear pressed against the door approximately an arm’s length away from the knock. What is different? You should have noticed that a more precise (and typically louder) sound reached your ear. If you pay close attention, you will also notice that the sound reaches your ear more quickly. This is roughly analogous to how changes in the water column will affect sound speed.

The final piece of equipment used regularly for surveys is a HorCon (horizontal control) station. This is a land-based station that will help to define accurate position in the water. It allows for greater precision with global positioning data. The signals of satellites responsible for global position are affected daily by changing atmospheric conditions. Moreover, the precise positions of the satellites themselves are actually not well known in advance. This may result in a GPS location moving a few centimeters in one direction or another. While this is not going to heavily impact your ability to find a Starbucks in a strip mall, it can have a definite impact on the accuracy of charts for navigation. The HorCon station always remains in the same place on land, and can therefore be used to calibrate the measurements being read in the survey waters nearby and that information can be used along with corrected satellite positions since it is coming after the fact.

Port Clarence chart

A nautical chart of the Port Clarence and Grantley Harbor area where we were surveying

Today we worked in Port Clarence, Alaska, both outside and inside of Grantley Harbor. Most of the depths being surveyed are in the 4-6 meter range. The particular area being surveyed had been previously surveyed in the 1950s by the US Coast and Geodetic Survey, likely using a single beam sonar system. The current survey is intended to note changes that have occurred since that prior survey and to accurately update all of the charts. The area of western Alaska is expected to increase in boat traffic over the coming years due to the opening of the Northwest Passage from the Pacific to the Atlantic via the Arctic. This route is significantly shorter for most shipping traffic than the route through the Panama Canal. Because of this expected increase in traffic, there is a need to identify areas for sheltering during heavy seas. Port Clarence is a natural inlet that offers some protection and holds potential for this purpose.

The process of surveying:
Two launches were deployed. I was on launch 2808, the second described here. The first was equipped with only multibeam sonar and the second had both multibeam and side scan. The plans for the two launches were different. The launch with only multibeam was working in an area of Grantley Harbor and covering an area that had previously been mapped to insure that the values were acceptably accurate. This focus existed primarily because of extra time available up in this area. The launch running the side scan was completing some unfinished work in Port Clarence and then did further work inside of Grantley Harbor. These areas, or “sheets” are described below. As a side note, small boat deployment is a fascinating and involved activity that I will discuss in a later blog.

Survey areas are broken up into sections known as “sheets” – each sheet has a manager. This person will be from either the NOAA Corps or a civilian member of the scientific survey team. The sheet manager will be responsible for setting up the plan for survey and doing all of the final checks after data has been gathered, cleaned and examined to determine if there are areas that should be rechecked or run again before it is completed and undergoes final processing.

A sheet manager will need to consider several questions prior to setting up the initial parameters for the survey. What is the depth being surveyed? What type of bottom is it? What type of coverage is needed? All of these factors will come into play when determining how the lines will be run – how long, how far apart, which sonar type, etc.
Once the plan is determined, it will be the job of the Operations Officer, LT Damian Manda, to parse out the duties and create a daily work plan to cover all of the areas. Each day, multiple launches will be sent out to gather data as described above. As the fieldwork finishes for the day, data will be transferred to a drive and then brought into the ship’s mapping room where night processers will begin the lengthy work of checking and cleaning the data so that it can all be ready for the final processing step prior to being sent to the client.

HMarshburn at computer

Senior surveyor Hannah Marshburn at the computer terminal in launch 2808

How good are those data?
There are several checks built into the data collection process. First, the survey team members on the launches are watching in real time. With three screens to work from, they are able to see what the sonars are seeing and can also set certain limits for the data that will alarm when something appears to be contrary to what’s expected. Night processors look for anomalies in the data like sudden inexplicable drops in depth in an otherwise flat surface or an extremely “noisy” area with little good data. Any area with a former survey will also be compared to the previous values with large differences signaling possible issues. Many trained eyes look at the data before it is accepted for charting and there will commonly be at least one return to an area to check and recheck prior to completion. One area in the current survey has continued to show odd results, so trained NOAA divers will dive the area to find out what is really going on.

Personal Log

So far this has been an amazing experience. I fully enjoy being among the crew of the Fairweather and living on the ship. It’s hard to say what my favorite part has been so far because I have honestly enjoyed all of it! Since we didn’t get underway until Monday, I had the opportunity on Sunday to roam around Nome with a couple of the other folks that are just here for two weeks, LT Joe Phillips and LCDR Ryan Toliver. I learned a lot more about both the NOAA Corps and the Public Health Service of which they are respectively a part. (These are two of the seven uniformed services – can you name the other five?) NOAA Corps officers are in command on all of the active NOAA commissioned ships and aircraft and you will learn a lot more about them in future posts. The PHS is an organization made up primarily of medical professionals. These folks serve in various medical and medical research positions around the nation. There are many who will work for the National Institutes of Health in research, or the Bureau of Prisons or commissioned vessels like Fairweather as practitioners. Unlike NOAA Corps, PHS is not on a billet cycle where every two to three years you will be moved to a new position in a different office or location. Similar to all of the other uniformed services, though, promotion through the ranks is both encouraged and desired.

Traditional Boat - Nome

As we walked all around Nome, this was one of the sights – the frame of a traditional fishing boat.

We also saw the marker for the end of the Iditarod race. I was able to see the historic beginning in Seward, Alaska back in 2010, so seeing the end in Nome was an unexpected treat. Nome also has Cold War-era missile early warning system arrays at the top of a mountain nearby. We had a chance to hike around them and see some of the interesting geologic features of the area. There’s so much more to talk about, but I think I’ll stop here and save shipboard life for my next post.

Did You Know…

… that the Iditarod has its historic beginnings with the Public Health Service? There were many children in interior and western Alaska dying of diphtheria in the early 1920s. When it reached epidemic proportions, the only doctor in Nome reached out to the PHS in the lower 48 to ask for help. Vials of serum were found and sent north to Seward, but then because of heavy ice and storming, dog sled teams were used to get the vials to the interior towns and to Nome. The original race along the Iditarod Trail was run as a memorial to the “Serum Run” and eventually evolved into the highly competitive race it is today.

Lisa Battig: Getting Excited for an Upcoming Adventure… August 18, 2017

NOAA Teacher at Sea

Lisa Battig

Aboard NOAA Ship Fairweather

August 28 – September 8, 2017


Mission: Hydrographic Survey leg IV

Geographic Area of Cruise: Alaska

Date: August 19, 2017

Weather Data from the Bridge (well, from my home city): 33.656311, -117.887800

I haven’t left yet, so I’ll just report on weather here in coastal southern California. It is a fairly typical August day, late morning temperatures in the high 70s, blue skies and a light 4 knot breeze from 235 deg SW. Yes, there is a reason so many people come to live here, but I’m personally ready for the far more extreme temperatures I will get to experience 30 degrees further north and 50 degrees further west!

Science and Technology Log

I have the privilege of being a part of the NOAA Ship Fairweather crew for 10 days. We will be off the coast of Alaska doing hydrographic surveys.  While I don’t totally know what to expect, I know that the end goal is mapping for navigation purposes and that the sonar can give some other information, too. Ultimately, that and other hydrographic survey data can be used to make maps and I LOVE maps. This one below (courtesy of USGS) shows the submarine canyons at the end of the Los Angeles River and the Santa Ana River off the coast of Southern California. It’s so cool to have a visual sense of what you’re surfing, paddling, swimming or fishing over.

A map of the submarine canyons at the end of the Los Angeles River and the Santa Ana River off the coast of Southern California (source: USGS)

So, what I do know about what we’re doing is that we’ll be taking side scan sonar data of an area around Nome, Alaska in the Bering Sea. I know that the ship will be running some predetermined patterns to add to an existent database that was begun with legs I, II, and III of this same mission. The ship, by the way, is the Fairweather(image courtesy of NOAA)

NOAA Ship Fairweather

NOAA Ship Fairweather (credit: NOAA)

She’s quite grand and I can’t wait to board and to meet all of the shipboard personnel and learn more about the operations firsthand. I’ll have lots of science and procedure and people to talk about in my next post, I’m sure.

Personal Log and Introduction

Lisa Battig, here! I’ve been teaching at Fountain Valley High School since 2007. Fountain Valley High School is a comprehensive public high school with about 3,800 students. I currently teach Chemistry and Environmental Science there and I love it!  “FVHS” is filled with teachers who are adventurous and willing to try new things. As a result, we’ve always had an administration that is exceedingly supportive of teacher ideas. The culture is collaborative, encouraging and exciting. I could not wish for a better school. Then there are the 3,800 talented young people who walk on campus every day who really make it a fun place to work. Here is an image of me with 64 of them (and lots of parent chaperones!) at Joshua Tree National Park this past January:



Fountain Valley High School students at Joshua Tree National Park

So a bit more about me…

I couldn’t tell the story of where I am now without paying homage to the great Bob Perry. You may not have the privilege of knowing Bob, but that man has inspired probably thousands of students over his career. He was my high school marine biology teacher who also was a master dive instructor, owned his own boat, wrote his own plankton keys, did photography on the side, expected his first year students to do real research and read journal articles, taught us DOS commands and some Basic so we could analyze our data on a computer (1987!!), and had his classes out in the field at the local pier weekly taking raw data. Not to mention he had a research permit and kept three enormous saltwater tanks in the back of his room holding local species so we would be familiar with them and kept a wet table in class that I used when I took an independent research course with him during my senior year.

I was challenged by him, certified in SCUBA by him, encouraged by him, directed by him, mentored by him and ultimately owe at least 80% of what I do in the classroom today to him and his methods.

That spark of interest in high school was the impetus for my undergraduate Marine Biology degree. The ocean was and still is one of my greatest passions. In my college years, I was again blessed with a professor who allowed me to help with his research on copepods and who made certain that we had plenty of time in the field doing trawls, dredges, plankton tows and so much more. Sadly, though, with just an undergraduate degree it was difficult to find anyone willing to pay me to sit in the ocean and hang out with dolphins all day. But my program had been broad and garnered me a minor in Chemistry, also. So out of college I went to work as an analytical chemist instead. That later led me into a varied and interesting career in technical sales and then finally into teaching. It was a good place for me to land – and it’s allowed me to indulge my desires to become more involved in Environmental Science. I went back to school for my MS in Environmental Science a few years ago and was able to develop a sanitation and hygiene education program to be used with small communities throughout the world. This is part of the program being used one on one by a volunteer in a village in El Salvador.

Applying Glo Germ

Sanitation and hygiene education program in El Salvador

I haven’t lost my love of the ocean, nor my love of research. These days, I indulge the former through surfing and offering my AP students the opportunity to get SCUBA certified. Their certification ends with a three day boat trip to dive spots all around Catalina Island. For the research component, I have my AP students develop their own field or lab research and present the findings in a poster session at the end of the school year. I also find whatever research might be available to me through summer programs and the like. I’ve been able to assist in two local university labs through Howard Hughes Medical Institute grants. The experiences have had broad impacts on me personally and definitely on my teaching as well.

Nias 2

A surfer off of Nias Island


(For clarification, I am behind the camera for this Nias Island beauty, not behind the sheet of water. It was the best surf trip of my life! But this one day was a bit too big for me.)

And finally, how I got involved with the NOAA Teacher at Sea program.

My first year of teaching in 2005, I had a mentor who was chosen to be a part of the Teacher at Sea program. His stories immediately sparked my interest in it and I started dreaming about where I might be able to go and what I might be able to do. Unfortunately, each year some challenge would prevent me from applying. Last November, though, all the pieces finally fell into place and I was able to get that application in. Now I find it almost impossible to believe that a 12 year dream is finally coming to fruition! Again, I am so thankful to have a supportive administration that is willing to let me miss some school so that I can bring real world research, application and STEM connections back into the classroom.

Did You Know?

The solar eclipse of August 21, 2017 will only cover approximately 28% of the sun in Nome, Alaska where I’ll be embarking. However, on March 30, 2033 Nome will be one of the few land masses to be awarded a total eclipse!