NOAA Teacher at Sea
Aboard NOAA Ship Okeanos Explorer
May 30 – June 14, 2019
Geographic Area of Cruise: U.S. Southeastern Continental Margin, Blake Plateau
Date: June 5, 2019
Latitude: 29°01.5’ N
Longitude: 079°16.0’ W
Wave Height: 2 feet
Wind Speed: 10 knots
Wind Direction: 128
Visibility: 10 nm
Air Temperature: 27.7°C
Barometric Pressure: 1021.3
Science and Technology Log
What is sonar?
Sonar is the use of sound to describe the marine environment. Sonar can be compared to satellites that use light to provide information about Earth, but instead of light, sound is used. It is used to develop nautical charts, detect hazards under the water, find shipwrecks, learn about characteristics of the water column such as biomass, and map the ocean floor. There are two types of sonar, active and passive. Active sonar is sonar that sends out its own sound wave. The sonar sends a sound wave (ping) out into the water and then waits for the sound to return. The return sound signal is called an echo. By assessing the time, angle, and strength of the return sound wave or echo one can learn many details about the marine environment. Passive sonar does not actively send out a sound ping, but rather listens for the sound from other objects or organisms in the water. These objects may be other vessels and these organisms may be whales or marine ecosystems such as coral reefs.
Sound waves move through the water at different speeds. These speeds are known as frequencies and the unit of measurement for sound is a hertz (Hz). Lower frequencies (example 18 kHz) are able to go farther down because they move slower and have more power behind them. It is like when a car goes down your street, pumping the bass (always seems to happen when I am trying to sleep) and you can hear it for a long time. That is because it is a low frequency and has longer wave lengths. Higher frequencies (example 200 kHz) move faster, but have less power. The sound waves should reach the bottom, an object, or biomass in the water column, but there may be no return or echo. High frequency sound waves are closer together. High frequencies give you a good image of what is happening near the surface of the water column and low frequencies give you a good idea of what is happening near, on, or under the ocean floor.
Type of Sonar on Okeanos Explorer
There are many types of sonar and other equipment aboard Okeanos Explorer for use during mapping operations. All have different capabilities and purposes. Together they provide a complete sound image of what is happening below us.
Kongsberg EM302 Multibeam Sonar
Multibeam sonar sends sound out into the water in a fan pattern below the hull (bottom) of the ship. It is able to map broad areas of the water column and seafloor from depths of 10 meters to 7,000 meters. Only the deepest trenches are out of its reach. It is the most appropriate sonar system to map seafloor features such as canyons and seamounts. The fan like beam it emits is 3-5.5x the water depth with a max swath range of 8 km. However, when you get to its depths below 5,000 meters the quality of the sound return is poor so scientists keep the swath range narrower to provide a higher quality of data return. The widest swath area scientists can use while maintaining quality is a depth of 3,300-5,000 meters. The user interface uses a color gradient to show you seafloor features (red=shallow and purple=deep).
Backscatter uses the same pings from the multibeam. People use backscatter to model or predict physical or biological properties and composition of the sea floor. The coloring typically is in grayscale. A stronger echo looks brighter in the image. A weaker echo looks darker in the image. It gives you a birds-eye view of seafloor characteristics such as substrate density and seafloor features.
An Expendable Bathy-Thermograph (XBT) provides you with information on the temperature gradients within the water. When the temperature profile is applied to a salinity profile (taken from World Ocean Atlas) you are able to determine sound velocity or the rate at which the sound waves can travel through the water. When sound moves through water it does not move in a straight line. Its path is affected by density which is determined by water type (freshwater or saltwater) and temperature. Freshwater is less dense than saltwater and cold water is denser than warm water. The XBT information accounts for sound refraction (bending) through various water densities. When near shore XBTs are launched more frequently because the freshwater inputs from land alter density of the water and temperatures in the water column are more varied. XBTs are launched less frequently when farther from shore since freshwater inputs are reduced or nonexistent and the water column temperature is more stable. However, ocean currents such as the Gulf Stream (affecting us on this cruise) can affect density as well. The Gulf Stream brings warm water from the Gulf of Mexico around the tip of Florida and along the eastern coast of the United States. Therefore, one must also take into account which ocean currents are present in the region when determining the launch schedule of XBTs.
Simrad EK60 and EK80 Split-beam Sonar
Split-beam sonar sends out sound in single beam of sound (not a fan like the multibeam). Each transducer sends out its own frequency (example 18 kHz, 38 kHz, 70 KHz, 120 kHz, and 200 kHz). Some frequencies are run at the same time during mapping operations. Mapping operations typically do not use the 38 kHz frequency since it interferes with the multibeam sonar. Data collected with the use of the EK60 or EK80 provides information about the water column such as gaseous seeps, schools of fish, and other types of dense organism communities such as zooplankton. If you remember my “did you know” from the second blog, I discussed how sonar can be used to show the vertical diurnal migration of organisms. Well the EK60 or EK80 is the equipment that allows us to see these biological water column communities and their movements.
Knudsen 3260 Sub-bottom Profiler
The purpose of using a sub-bottom profiler is to learn more about the layers (up to 80 meters) below the ocean floor. It works in conjunction with the sonar mapping the ocean floor to provide more information about the bottom substrate, such as sediment type and topography features. Sub-bottom data is used by geologists to better understand the top layers of the ocean floor. A very low frequency is used (3.5 kHz) because it needs to penetrate the ocean sediment. It will give you a cross section of the sea floor so floor features can be detected.
Telepresence aboard the ship allows the science team to get mapping products and raw data to land on a daily basis. The science team can also live feed data collection to shore in real time. By allowing a land based shore team to see the data in real time you are adding another system of checks and balances. It is one more set of eyes to make sure the data being collected looks correct and there are no issues. It also allows a more collaborative approach to mapping, since you are able to involve a worldwide audience in the mission. Public viewers can tune in as well. Support for the technology needed to allow telepresence capabilities comes in partnership with the Global Foundation of Ocean Exploration (GFOE). With GFOE’s help, the protocols, high-speed satellite networks, Internet services, web and social media interfaces, and many other tools are accessible when out to sea. The NOAA Office of Exploration and Research (OER) provides the experts needed to develop, maintain, and operate the telepresence systems while at sea, but also at shore through the Exploration Command Centers (ECCs) and the University of Rhode Island’s Inner Space Center.
All in all, the equipment aboard Okeanos Explorer is impressive in its abilities to provide the science team with a high quality and accurate depiction of the ocean floor and water column. The science team aboard is able to interpret the data, clean out unwanted data points, store massive data files on computers, and send it back to land daily, all while rocking away at sea. Very impressive and very cool!
I learned all about memes today. Apparently they are very popular on the ship. So popular, we are even in the middle of a meme contest. For those of you unfamiliar to memes like I was, a meme is a funny picture with a clever caption that makes you laugh or relates to something in your life. After my tutorial in meme making, we had a great time out on the bow of the ship playing corn hole and hanging out. The night was beautiful. The humidity subsided and there was a great breeze. After the sun set, I watched the stars come out and then went inside to learn more about the mapping process. I am starting to get a better understanding of what the science team is doing. You know the how and the why of it all. After I couldn’t keep my eyes open any longer, I made my nightly venture out onto the bow to look from some bioluminescence, the glittering of zooplankton in the night. A magical site. I will leave you wondering how the ocean glitters until one of my future blogs when I describe the process of bioluminescence.
Did You Know?
The SOFAR (Sound Fixing and Ranging) channel occurs in the world’s oceans between depths of 800 to 1000 meters in the water column. Because of the density and pressure around this channel, sound waves travel for an extended distance. It is thought that fin whales travel to this channel to communicate with other fin whales many kilometers away.