Eric Koser – Page 2 – NOAA Teacher at Sea Blog

June 28, 2018

Eric Koser: Let the Science Begin! June 27, 2018

NOAA Teacher at Sea
Eric Koser
Aboard Ship Rainier
June 22-July 9
Mission: Lisianski Strait Survey, AK
June 27, 2018: 1500 HRS

Weather Data From the Bridge
Lat: 57°52.9’ Long: 133°33.8’
Skies: Overcast
Wind 15 kts at 011°
Visibility 10+ miles
Seas: Calm
Water temp: 3.9°C

Science and Technology Log

Rainier Hat — This insignia cap is worn by the NOAA Corps members on the ship.

Let the science begin! We departed from Sitka about 1300 on Monday enroute for Lisianski Inlet. Getting out to sea has been a wonderful experience. Ship Rainier is truly run by a dedicated team of people. I have been able to spend quite a bit of time on the bridge – first watching and then participating with the Junior Officers on the deck. It quickly became obvious to me that this is a teaching operation. The hands on the deck represent a variety of experience levels, quite by design. More experienced NOAA Corps Officers coach Junior Officers through each procedure that happens on the Bridge. It’s a great example of a team based ‘on the job’ teaching system!

On the bridge there is always an OOD (Officer On the Deck) that is in charge of operations. This person then helps to administrate the work of the CONN (responsible for the conduct of the vessel), the helm, the lee helm, the lookouts, and the navigator. The CONN gives commands to the others on the team, which are then repeated back to assure clarity.

Chart Table — This is the chart table where the Navigator works on the bridge of the ship.

The first task I learned was to plot our course on the charts. The CO (Commanding Officer—in charge of the entire ship) selects waypoints for an upcoming course in a digital mapping suite called Coastal. Coastal sets a series of digital paths that each include a compass bearing (direction in degrees) and range (distance in nautical miles) between each waypoint. Then the navigator takes this same series of points and plots them by hand in pencil on the series of chart {the nautical term for maps]. Each point is a pair of latitude and longitude points plotted as a small square. Given the expected cruising speed, the navigator can also estimate future positions of the ship, which are referred to as “dead reckoning” and are plotted with a half circle.

Sheet Route — A route that I plotted on our charts.

A view from the Coastal software of a route.

Periodically the navigator measures the location of the ship either digitally with GPS or by measuring distances to adjacent land features with radar. A pair of dividers is used to plot these distances on the sheet as small triangles and confirm the current location of the ship. By these methods, the navigator assures the ship is on the planned track and/or adjusts the track accordingly.

The person at the helm (the steering wheel) is directed by the CONN to point the ship at the necessary bearing. As changes are needed to the bearing, the person at the helm responds to the CONN’s commands to adjust.

In Lisianski Inlet the team of hydrographers started collecting data with the multibeam sonar system around midnight Tuesday morning. As we traveled along the entire length of the Inlet overnight, this initial data was collected. When we arrived at the small town of Pelican, AK (pop. 88) a crew on a launch (small boat deployed from Rainier) traveled in and set up a HORCON (Horizontal Control) reference station. This is a high precision satellite receiver. It provides a very accurate way to measure potential drift in satellite indicated GPS over time. After taking data from the ship, the latitude and longitude are corrected with data from the HORCON.

Launch RA — This is one of several small(er) boats called “Launches” that are used for surveying.

Ship Rainier — This is a view of our ship from the launch.

After this initial work was complete at Lisianski, we began transit to Tracy Arm Fjord. While the multibeam sonar work was completed here last week, three crews deployed in launches to ‘proof’ the shoreline information on the charts. This is essentially confirming and updating the existence and location of particular features (rocks, ledges, etc).

Launch Team — NOAA Hydrographer Amanda Finn and I together on the launch.

At this point, the hydrographers are processing much of the data obtained in the past few days. Additional data will be collected tomorrow morning. Then in the evening we’ll transit back to Lisianski to begin further work there.

Ship among ice. — The ship parked here while the launches moved closer to the ice.

Glacial Ice — The glacial ice shows a beautiful blue color.

Ice Blue — Different pieces of ice appear slightly different colors.

Personal Log

Every member of the team on this vessel has a job to do. Every member matters. The success of the entire operations depends upon the teamwork of all. There is a positive sprit among the group to work together for the tasks at hand.

I’ve been welcomed to learn to chart our course. I had an opportunity today to operate the helm (steering). I went out on a launch today to visit waters that were yet uncharted as the glacier at the end of Tracy Arm Fjord is receding. It was incredible to see not only the beauty of the ice among the water, but to also witness from afar the calving of the glacier. A rumble like thunder accompanied the crashing of two small walls of ice into the ocean below as we watched from afar.

I enjoyed capturing many photos of the ice and the wildlife among it. Many harbor seals were relaxing upon chunks of glacial ice as we traveled through the Arm. The natural beauty of this area is best represented by a few photos.

An adult seal and pup — This adult seal was watching us closely with the pup.

Ice Dog? — What can you see in this ice? Might it resemble a dog?

Did You Know?

Junior Officers in the NOAA Corps learn in a 19 week program followed by 2 weeks at sea on a tall ship called Eagle.

There are approximately 320 commissioned officers in the NOAA Corps internationally.

NOAA Operates 16 Ships and 20 Aircraft!

June 26, 2018

Eric Koser: Getting Underway! June 25, 2018

NOAA Teacher at Sea

Eric Koser

Aboard NOAA Ship Rainier

June 22 – July 9, 2018

Mission: Lisianski Strait Survey

Geographic Region: Southeast Alaska

Date: June 25, 2018, 1500 HRS

Weather Data From the Bridge
Lat: 56°59.4’, Long:135°53.9’
Skies: Broken
Wind 19 kts at 340°
Visibility 10+ miles
Seas: 3-4’ with swells of 2-3’
Water temp: 9.4°C

Science and Technology Log

Rainier and her sister ship Fairweather celebrated their 50^th anniversary together this past March. The bell on the bow of each ship is now plated in gold to celebrate the event.

This vessel has quite a physical plant below deck maintained by the competent team in the Engineering Department. For propulsion, there are two V-12 Diesel Locomotive Engines. After bathing the valves in fresh oil, each engine is started with compressed air at the press of a button. Once up and running, the Rainier’s engines often run for several days at a time. There is no “transmission” on this vessel. Instead, the two propellers utilize what is called ‘variable pitch’. When the pitch is set to zero, the props spin but push water neither back or forward – and thus don’t force the ship to move. When the prop pitched is increased in a forward direction – up to a pitch of 10, the ship is pushed forward. Of course, this is really the water pushing the ship forward as the propellers push the water backward. A pitch of “10” means that for each single rotation of the prop, the blades will move water ten feet back. When reverse is desired, the props can each pitch back to a maximum of ‘6’. Now the water is pushed forwards by the prop so the water can push the ship backward.

Prop Pitch Control — This is the variable prop pitch control system. Notice the silver digital actuator at the top which provides an electronic signal back to the bridge.

Push to Start — This is how the Engineering Department can start the engines.

As there are two engines and two propellers, the Rainier’s crew can run one prop forwards and the other backward to turn the vessel around nearly in place. This could be called a ‘split 6’ – where one prop is pitched forward 6 to match the other prop’s pitch backward of 6.

Rainier Engines — This is one side of one of Rainier’s two V-12 Diesel locomotive engines.

Another device the crew can use to manipulate the ship in the water is called a ‘bow thruster’. This is an open tube from port (left) to starboard (right) near the bow of the ship underwater. There is a propeller mounted in this open tube which is powered by a separate engine. The engineering team can have the bow thruster system up and running in just a matter of minutes when called on by the bridge to prepare for its use! By pushing water to one side, the water pushes the bow the other way. This is a great tool to maneuver this large vessel in tight spaces.

In addition to the two engines plus the bow thruster, there are several other important systems maintained on The Rainier. There are a pair of 4000 Watt diesel electric generators to provide electricity. There is a water purification system – to isolate salt from seawater and make clean drinking water and a wastewater treatment plant to process waste. There are air compressors to supply the ship’s systems.

There are 45 individuals on board this ship – and they pull together into five teams to make operations happen on board. The NOAA Corps is responsible for the administration and navigation of the ship. The Deck crew handles all things on the surface of the ship including handling all lines, cranes, and davits (to manipulate the launches—small boats). The Engineering Crew is responsible for all the mechanical systems on board. The Electronics Department handles all instrumentation and wiring on the ship. The Stewards run the ever important galley – keeping the entire group well fed. All of this supports the work of the survey team of Hydrographers, the team of scientists that are mapping the sea floor.

Personal Log

I’ve enjoyed both finding my way around the ship and getting to know the crew. These people work as a team!

I came in early enough to enjoy a few days exploring Sitka, Alaska. This is a small port town that is really the first city in Alaska. Russians originally settled here in 1799 and eventually sold the city to the US in 1867. Sitka is a beautiful place to explore – being primarily a port for commercial and private fishing operations.

Sitka Bridge — This bridge spans the main channel in Sitka.

Sitka Harbor — This is one of Sitka’s many harbors.

We’ve just left port this afternoon [Monday] as we transit to Lisianski Strait to being the hydrographic mission of this leg. We’ll arrive there late tonight/early Tuesday morning to collect data first from the Rainier itself. The experience on the ocean has been great thus far, and I look forward to much more!

Here we are departing Sitka Monday afternoon – headed to the open Pacific to transit north.

Did You Know?

Sitka is the largest city, by area, in the United States in terms of land area! It occupies 2870 square miles yet has only a population of about 9,000 people—located mostly on the port location of Sitka.

The Rainier holds about 80,000 gallons of diesel fuel that is located in several tanks below deck. The weight of the fuel serves as ballast to help keep the ship stable while at sea! Fuel can be shifted between tanks to adjust the trim [front or back tilt] and list [port or starboard tilt] of the ship. Typically Rainier refuels when the tanks reach about half full.

June 21, 2018June 21, 2018

Eric Koser: Welcome– Its Almost Time! June 21, 2018

NOAA Teacher at Sea

Eric Koser

Aboard NOAA Ship Rainier

June 25 – July 9, 2018

Mission: Hydrographic Survey of navigable waters to develop and update navigational charts. At sea June 25 – July 9, 2018.
Geographic Area of Cruise: Lisianski Strait, along the SE coast of Alaska followed by transit of the Inside Passage to home port in Newport, OR.
Date: June 21, 2018, the Summer Solstice!

Weather Data from the Bridge [okay, the front porch at home!]:

44.1589° N, 94.0177° W
Current Weather: Light Rain, 70°F (21°C)
Humidity: 79%
Wind Speed: E 15 mph
Barometer: 29.81 in
Dewpoint: 63°F (17°C)
Visibility: 10.00 mi

Welcome!
It’s nearly time to embark on this adventure! I’ve always appreciated chances in life to explore and learn about different parts of the world. Recently I’ve enjoyed the book “One Earth, Two Worlds” by the Minnesota SCUBA diver Bill Mathies. I’m fascinated by the realm of underwater exploration. A large percentage of our planet has never even been seen by humans! NOAA’s hydrographic research vessels are in place around the world to map the ocean floor and promote safe navigation.

Science and Technology Log
I am Eric Koser and I live in southern Minnesota where I have worked with students learning about physics for 24 years. I teach at Mankato West High School, one of two mid-sized high schools in our river community of about 100,000 people. Mankato and North Mankato are the regional hub of south-central Minnesota. Our school district is home to about 9000 students K-12. Our community has particular strengths in manufacturing, education, and healthcare. Read more here at greatermankato.com!
I teach a variety of physics courses at West including AP Physics and Physics First at grade 9. I love to engage kids in learning physics by helping them to discover patterns and systems in nature. I really enjoy developing experiments and demonstrations to illustrate ideas. I also coach our YES! Team as a part of our Science Club here at West. Youth Eco Solutions is a program to support students to make positive energy and environmental based changes in their communities. These kids have tackled some big tasks – replacing styrofoam lunch trays with permanent trays, updating our building lighting’s efficiency, and systematically monitoring campus electrical usage.

Mankato West Scarlets

YESmn

Mankato Area Public Schools

Personal Log
My wife Erica and I have four kids that we love to support. They are currently ages 20, 18, 15, and 10 and always on the move. Our oldest, Josh, is an engineering and technical theater student at the U of MN. Our next, Zach, just graduated from high school and is rebuilding a small hobby farm and an 1800’s house to become his rural home. Ben is an avid photographer now working at a local photo studio shooting professionally for events. Meron is headed to fifth grade– she is our most social kid who loves being with her friends and our many pets here at home.

Our summers often involve many days at ‘the lake’, a place we enjoy in northern Minnesota with extended family. We love to fish, swim, kayak and explore the water there. As a SCUBA diver, I’ve begun to explore below the surface of the water as well.

SCUBA MN — Lake diving in Minnesota can be chilly! – Photo by Ben Koser

MN Lake Sunset — Ben captures the last of this Minnesota lake sunset – photo by Eric Koser

This summer has also involved lots of construction on Zach’s farm as we bring a once gutted two-story house into a finished home.

MN Hobby Farm — Zach’s Minnesota Hobby Farm – photo by Eric Koser

In a few short days, I look forward to joining the NOAA Ship Rainier on a hydrographic survey of Lisianski Inlet on the SE coast of Alaska. I’ll meet up with the Ship in port at Sitka, Alaska.

The Rainier is a 231 foot long ship equipped with a variety of tools to digitally map the bottom of the ocean with the goal of updating and improving navigational charts. I look forward to meeting and working alongside the experts on Rainier while I learn everything I can about the important work that they do. I look forward to bringing questions and ideas to my students and community during and after this experience!

Questions!

The Rainier design specifications list a “draft” of 14.3 feet. What does this mean?

This ship displaces 1800 tons of water. What does this mean?

How could you determine the ‘footprint’ of the ship in the sea based on these two pieces of data? What is the average area of the footprint of this ship?